PROJECTS


 

A selection of our projects below showing just how versatile the PH15 system is in transforming your design ideas into Passivhaus reality.

Hackney N4

A new dwellings designed to passivhaus standard by Arboreal Architects, part of the 15:40 group. Planning conditions mean this has to perform to the Passivhaus standard. The PH15 System was chosen for the ease of achieving the required standard and because of the access restriction of the site.


Passivhaus statistics:

TFA : 136.2m²
Form Factor 3.4, with U-values of walls 0.078W/m²K, roof 0.07W/m2K, floor 0.077W/m2K.  

Provisional: Heating Demand 13.9 kW/m²a. Heating Load 7.95 W/m²

 

Due on site Spring 2017


Camden NW5

Two new dwellings designed to planning stage by Bere Architects on a small site previously occupied by 6 lock-up garages. Due to the poor form factor the houses meet the Passivhaus Institute Low Energy Building Standard which allows a heating demand between 15 and 30 kWh/m²a rather than the stricter full Passivhaus standard of below 15 kWh/m²a.


Passivhaus statistics:

TFA : 148.5m²
Form Factor 4.31, with U-values of walls 0.078W/m²K, roof 0.104W/m2K, floor 0.12W/m2K.  Heating load 12W/m2.
Heating Demand 25 kWh/m²a

 

Currently under contruction

Camden Frame

Littlepits Passivhaus

A five bedroom detached house, a replacement dwelling in the Chilterns Green Belt. The design had to meet the exacting Chilterns Design Guide and to address planning concerns on visual impact on the Green Belt. The house is a mix of lime render, brick, and timber cladding and includes two green oak porches. The house also incorporates a Glathaar basement system which PHH has detailed to the Passivhaus standard.


Passivhaus Statistics:

TFA 317sqm

Form Factor 2.43 with average wall/roof U value 0.085W/m2K, floor 0.07W/m2K, average whole window/door U values from 1.02-0.85W/m2K. Heating demand 11.1 kWh/m²a, heating load 7.3 W/m2

Currently on site. Construction by Jigsaw Design and Construction Ltd

projects at the beginning - view of plans

Riverways, Devon

Bespoke new build detached house (net floor area 208sqm) designed to planning stage by architect Chris Donoghue and then detailed and constructed using the PH15 System – the design needed some modifications by us to hit the Passivhaus standard. Construction started on site April 2015 by Passivhaus Homes Ltd.

External finishes are a mix of lime render and western red cedar boarding. Windows and doors Katzbeck Linea range.


Passivhaus statistics:

TFA 193.8 m² Building Form Factor 2.79 with average wall U-value 0.09W/m²K, floor 0.11W/m²K, roof 0.10W/m²K, and average installed whole window/door U values 0.88W/m²K.

GFA 208m²,  PH15 System components £115,000

Constructed by Passivhaus Homes Ltd
Completed Spring 2016.
Follow the Clients Blog

Certified Passivhaus

PHI-logo


Riverways front elevation

Akerman Rd, London SW9

This is a project for Lambeth Council for three new Passivhaus terrace houses. The site is an urban infill on a typical London street. The design is by Anne Thorne Architects and we have completed the working drawings to construct using our PH15 System. The project included 6 retrofit flats which have been detailed by Prewett Bizley Architects. Finishes are a mix of lime render, brick entrance porches, brick slips and reconstituted slate roofs. This project is the first collaborative project for the 15-40 Architecture Collective and our first use of the PH15 kit for social housing provision.


Passivhaus Statistics:

TFA 371sqm

Form Factor 1.8, with U-values of roof 0.108W/m2K, walls 0.105W/m2K floor 0.106W/m2K.  Heating load 7.9W/m2. Predicted Heating demand 9.1 kWh/m²a

Airtightness test results:0.34, 0.39 and 0.4 ach

Construction by Sandwood Construction Ltd

Completed December 2016

Certified Passivhaus

PHI-logo


Ha Ha House, Torquay

Designed by architect Richard Maddock for his own home, this is a single storey modern design sited in front of an old stone retaining wall, creating a striking juxtaposition of old and new.

Passivhaus Homes collaborated on modifications to the original design to bring it up to Passivhaus performance standards, and then detailed the construction package using our PH15 System.

External finishes are lime render and wood cladding with a living roof. Windows and doors are Katzbeck Linea.


Passivhaus Statistics:

TFA 133sqm

Form Factor 4.1, with U-values of walls and roof 0.076W/m2K, floor 0.071W/m2K.  Heating load 9.8W/m2. The single storey design makes getting to Passivhaus a challenge (see the poor form factor), but good junction details achieved by the PH15 System resulted in negative linear cold bridges.

GFA 139m², PH15 System components £79,000

Completed Autumn 2016. Construction by Passivhaus Homes Ltd.

Ha Ha artists impression

Tring Passivhaus, Chilterns

This detached 3-bed house (net floor area 122sqm) is to be built in the rear garden of a house in the High Street Conservation Area in Tring town. The house is a modification of our generic 3-bed house using the Passivhaus Homes PH15 System. External finishes are a mix of lime render, timber cladding with plain clay tiling on the roof with oak end rafters. Specification includes a Lacuna folding/sliding screen door and Katzbeck windows.


Passivhaus Statistics:

TFA 110sqm

Form Factor 3.2 with average U-values of walls and roof 0.08W/m2K, floor 0.07W/m2K. Space heating demand 13.6kWh/sqm.a.
GFA 122m², PH15 System components £79,917
Initial air test result 0.3 ach

Completed summer 2016. Construction by RAK Construction Ltd

Certified Passivhaus

PHI-logo

 

Completed house viewed from the High Street

Butchers Arms redevelopment, Plymouth

A 3-bedroom detached house adjacent to the Grade I listed Royal William Yard. A mix of lime render, slate hanging, slate main roof and secondary living roof with oak framed open terrace area. Although the site had a previous planning refusal we were able to develop an alternate design to satisfy the planner’s particular concerns around design, setting and visual impact.


Passivhaus Statistics:

TFA 127.5sqm

Form Factor 3.3, with average wall/floor U value 0.09W/m2K, floor 0.11W/m2K, space heating demand 12.4 kWh/m2.a  

Due on site Summer 2015.


Berrydown, Mid-Devon

A three bedroom detached Passivhaus using an innovative ‘portal frame’ design eliminating thermal bridges at the first floor, eaves and ridge using a simple construction method. The innovative timber portal frame construction removes the need for a central ridge beam (simplifying air-tightness details), and enables fully filling of the walls and roof as a single element. The first floor is hung off a ring beam fixed back to the portal frame members. This removes any thermal bridging at the wall/floor junction and again simplifies construction of the air-tight layer. The building design meets the clients contemporary design preference for a minimalist eaves detail while also reflecting the local barn vernacular in this region of mid-Devon. This is a contemporary Passivhaus for a young family suitable for its Conservation setting in an English rural village.


Passivhaus Statistics:

TFA 113sqm

Form Factor 3.29, with U-values of floor 0.07W/m²K; wall 0.09W/m²K; roof 0.10W/m²KDesign space heating demand: 13.8kWh/m² per annum; heating load 9.3W/m²

Completed July 2013.

the finished house viewed from the hill

Totnes Passivhaus

One of the UK’s first Certified Passivhaus refurbishment projects being a hybrid retrofit with new build extension achieving the full passivhaus standard. The extension is made from timber frame, uses recycled newspaper insulation and has a living roof. The house also has a photovoltaic array and solar hot water panels. The design achieves below the 15kWh/sqm requirement for space heating (90% less than the average UK) Total Primary measured energy in use is 75.8KWh/sqm.a The project was completed in July 2011 – the final air tightness test was an impressive 0.19 ach at 50 Pa (Passivhaus standard is 0.6 ach). This makes Hunters Moon the most leak free retrofit house in the UK!


Passivhaus Statistics:

TFA 162sqm

Form Factor 2.62, with U-values of walls and roof 0.01W/m2K, design space heating demand: 13.3kWh/m² per annum; heating load 9.3W/m².

 

Completed 2011

Certified Passivhaus and Winner of the 2013 Passivhaus Trust Awards

PHI-logo


RIBA logo
Passivhaus Trust Member
15 40 architecture collective
certified passivhaus consultant